• Wall brackets
• Desktop racks
• Wall mount racks
• Rack shelves
• Relay racks, 2-post
• Relay racks, 4-post
• Horizontal cable managers
• Screws and accessories

• Hammond Cabinets
• Hammond Power Strips
• Premise Wiring Products
• Network patch cables

• made of 16 gauge steel with black powder coat finish
• includes 8x #10-32 clip nuts
• rear keyhole mounts and cable tie slots
• 70 lbs maximum load recommended

Perfect for small office, test bench, or workgroup applications. Fits standard 19 inch rackmount equipment like patch panels, switches, hubs and PDUs. Available in three depths.

• Heavy duty, 16-gauge steel, 19” table top cabinet.
• Ventilated sides to allow natural air convection.
• Includes two pairs of adjustable rails, rubber feet, black plastic handles, clip nuts & screws.
• Ships unassembled (four cabinet pieces & four rails) in a flat pack container.
• Overall width 21”. Overall height 2” over panel space.
• Front & back lip is .585" so usable depth is reduced by 1.17"
• Recommended maximum weight 800 pounds.
• Rugged textured black powder paint finish.

Perfect for SOHO (Small Office, Home Office) applications for servers, storage & networking. Supplied unassembled (four cabinet pieces & four rails), requires only a screwdriver to assemble. Optional perforated doors, fans, casters, and stacking/ganging kits available. Available in three depths and 12U or 24 heights.

• Simple assembly using one bolt in each corner to lock the sides to the top and bottom.
• Shipped in a flat pack container for handling ease & protection.
• Heavy duty, 16-gauge steel, 19” rack mount cabinet.
• 12U version is 25" high (fits under most desks).
• Easily stacks and/or gangs to other units.
• Includes two pairs of adjustable square hole rails, and 50 screws and cage nuts
• Overall width of 24” provides space for cabling.
• Generous cable-entry "punch-outs" with gasket.
• Front & back lip is .75" so usable depth is reduced by 1.5"
• Recommended maximum weight - 1,500 pounds.
• Rugged textured black powder paint finish.

Ideal for protecting workgroup equipment like switches, hubs and patch panels. Available in four heights.

• Economic design - 19” wall mount rack cabinet.
• Ventilated slots front & side.
• Pre-punched top with cover plates for optional fans.
• Cable access panels top & bottom.
• Includes two pairs of square hole mounting rails with 20 screws and cage nuts.
• Locking tempered glass door opens a full 180 degrees.
• Ships unassembled in a flat pack container.
• Overall height - add 3/8" for mounting hardware .
• Maximum static load weight - 130 pounds.
• Rugged black powder paint finish.

Ideal for protecting workgroup equipment like switches, hubs and patch panels. Swingout design allows rear access to equipment. Available in five heights.

• Economic design swingout wall mount - 19” cabinet.
• Ventilated slots front & side.
• Body is hinged from wall mount section - 3.9" (100 mm) depth
• Pre-punched top for optional fans.
• Cable access panels top & bottom.
• Removable side panels.
• Includes 2 pairs of square hole mounting rails with 20 screws and cage nuts
• Smoked tempered glass door with lock opens a full 180 degrees and can be hinged either side.
• Shipped assembled - ready to install.
• Maximum static load weight - 130 pounds.
• Rugged black powder paint finish..

Ideal for protecting workgroup equipment like switches, hubs and patch panels. Swingout design allows rear access to equipment. Available in three heights and two depths.

• Standard 19” rack panel width mounting
  
• 3 hinged sections with quick release latches
  
• Includes one pair of infinitely adjustable - combination rack mount rails, on E.I.A. universal spacing (5/8 - 5/8 - 1/2 inch) drilled & tapped for 10-32 screws
  
• Choice of two depths - 11 or 20 inch deep center section (17.5 or 26.5 overall)
  
• Ventilated center section
  
• Lockable, smoked plexi front door (reversible by moving three hinges on enclosure)
  
• Lockable rear wall mount section with keyhole mounts
  
• Cable access knockouts top and bottom
  
• Heavy duty construction, 14 gauge steel
  
• 100 lb. weight load capacity
  
• Powder paint textured black finish.

• made of 14 gauge steel with black powder coat finish
• available vented or solid

• made of 10 gauge steel with black powder coat finish
• tapped #10-32 on front flange
• bolt down 15x20 base plate
• weight tested to 1530 pounds
• optional RRCM vertical cable managers can be attached to one or both sides (see photo right)

• made of 12 gauge steel with black powder coat finish
• tapped #10-32 on front flange
• stable 20x20 base plate
• weight tested to 800 pounds

• made of black aluminum (plain finish shown in photo)
• tapped #12-24 on front and back flanges
• bolt-down 16x20 base plate
• weight tested to 850 pounds
• includes 30 screws
• supports ganging with other manufacturer's racks

• depth adjusts frtom 24 to 36 inches to fit most equipment
• universal 19 inch square hole mounting rails with 50x #10-32 cage nuts and screws
• bolt down stability bracket with toe-in or toe-out option
• weight tested to 2000 pounds

[+] Enlarge

Perfect for organizing cables in racks, cabinets or wall brackets. Various models and sizes available.

• Clip nuts for round hole rails on wall brackets
• #12-24 for aluminum racks
• #10-32 for steel racks
• Use cup washers with countersunk screws

TopCopyright 2008, Lex Tec Inc.
3251 Kennedy Road, Units 23-24
Scarborough, Ontario, M1V 2J9 Canada

Call us for molded cables, custom cables and wire harness assemblies!
Toronto, Markham and Mississauga 416-292-9979
Toll-free Canada and USA 1-800-665-9619